Assembly Instructions: 1323-9 WG (Ella)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completelyremovetheoldxturefromtheceiling,includingthe
oldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.One
endofnipple(F)shouldbeattachedtomountingstrap(A)with
hexnuts(C,D)inplace.Theotherendshouldhavecanopyloop
(H) attached.
Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.Unscrewcanopy
loop collar (I) from canopy loop (H). Pass canopy (G) over the
mountedcanopylooptotesttheheight.Approximatelyhalf
ofthecanopyloop’sexteriorthreadsshouldbeexposed,and
thecanopyloopcollarshouldtsnuglyontothecanopyloop.
Removecanopy(G)andadjusttheheightofnipple(F)and
canopyloop(H)untilthedesiredheightisreached.
ASSEMBLING THE FIXTURE
Twisttopcap(T)ontoxturebody(U)unitlsecure.Rotatethe
armsofthextureuntiltheyareinposition.Usedecorativenuts
(P)toattacharms(O)toposts(N)ofthexturebody.Referto
thecrystalinstallationsheettohangthecrystals.
Bymeasuring,determinethecorrectnumberofchainlinks
neededforproperhangingheight.Ifnecessary,useapair
ofplierstoopenandremoveanyexcesschain.Attachone
chain connector (K) to each end of chain (J). Use one of chain
connectors (K) to attach chain (J) to top loop (L) and close the
chainconnector.Feedthexturewiresupthroughthechain
(everythreelinksorso),pullingthewiresuntiltaut.Slidecanopy
loop collar (H) and canopy (G) onto the chain/wire. Use the free
chain connector (K) to attach chain (J) to canopy loop (H).
CONNECTING THE WIRES
Haveanassistantsupportthextureweightwhilecompleting
thewiring.Cutawayexcesswire.Threadthexturewires
throughcanopyloop(H)andnipple(F).Attachthexture’swires
tothepowersupplywiresfromthejunctionbox.Connectblack
toblack(orsmooth);whitetowhite(orribbed);groundtoground
(greenorcopper).Twisttheendsofthewirepairstogether,then
twist on a wire connector. Make sure all twists are in the same
direction.Ifthereisnogroundwire(greenorcopper)fromthe
junctionbox,locategroundscrew(E)onmountingstrap(A)and
wrapthexturegroundwirearoundthegreengroundscrew(E).
Useascrewdrivertosecuregroundscrew(E)ontothemounting
bracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)
upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)onto
canopy loop (H) to secure canopy (G) in place. Slide candle
sleeves (R) onto sockets (S). Install bulbs (Q) (not included) in
accordancewiththexture’sspecications.Donotexceedthe
maximumwattage.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
A
E
B
D
C
G
I
K
L
O
S
N
P
U
R
T
J
M
H
F
Q
Kommentare zu diesen Handbüchern